|
Digital Tracking Pedestal Solution / AL-4012
|
|
AL-4012 is orbit’s new generation lightweight, high-dynamic elevation-over-azimuth Digital Tracking Pedestal, equipped with brushless servomotors and a planetary gearbox as well as an absolute encoder for each axis. High accuracy - can be hand carried by two persond if needed.
|
|
|
Digital Tracking Pedestal System / AL-4016
|
|
The AL-4016 is orbit’s new generation lightweight, high-dynamic elevation-over-azimuth Digital Tracking Pedestal, equipped with brushless servomotors and a planetary gearbox as well as an absolute encoder for each axis. For high accuracy.
|
|
|
|
|
|
|
Indoor Tracking Controller / AL-4000
|
|
Orbit’s Antenna Control Unit (ACU) model AL-4000 (indoor unit) is an advanced tracking controller, designed to provide overall control of tracking antenna motion, display position and tracking data.
|
|
|
Outdoor Tracking Controller / AL-5005-3T
|
|
Orbit’s Antenna Control Unit (ACU) model AL-5005-3T (outdoor unit) is an advanced tracking controller, designed to provide overall control of tracking antenna motion, display position and tracking data.
|
|
|
|
Digital Servo Amplifier / DSA
|
|
The Digital Servo Amplifier (DSA) is a new generation of the servo driver for brushless motors with sinusoidal as well as trapezoidal commutation. The DSA is able to close not only motor current loop, but also velocity and position loops providing overall control of a servo axis.
|
|
|
Dual Digital Servo Amplifier / DDSA
|
|
Orbit’s AL-2006-DDSA-1A Dual Digital Servo Amplifier (DDSA) is a Digital servo driver for brushless motors. It drives both axes of the pedestals.
The DDSA is a DSP-based unit responsible for motor current, motor velocity and axis position control loops as well as comprehensive build-in test (BIT) of the entire pedestal.
The DDSA supports several digital serial interfaces: UART, SPI and CAN bus.
|
|
|
|
Hand-Held Remote Control Unit / AL-2005-LCU
|
|
The AL-2005-LCU is an Ultra compact, cost effective Hand-Held Remote Control Unit designed to manually control and display the position of Elevation over Azimuth Digital Tracking pedestals.
The LCU is ideal for service technicians and/or applications requiring manual operation only.
|
|
|
RCU Remote Control Unit / AL-2005
|
|
The AL-2005-RCU is an Ultra compact, cost effective Hand-Held Remote Control Unit designed to manually control and display the position of an Elevation over Azimuth Digital Tracking pedestals.
The RCU is ideal for service technicians and/or applications requiring manual operation only.
However, the RCU can be also connected to a host computer via RS422 comm. link while switching the” Local/Remote” switch to “Remote position”.
|
|
|
|
|
|
Airborne Tracking Antenna Positioner / AL-1610-1E EL/AZ
|
|
Airborne Tracking Antenna System for air to ground data-link on an aircraft, in order to provide 360º coverage. The system incorporates two antennas per aircraft, one of which is mounted in the tail-cone and the other in the forward belly radome. The antenna is a parabolic 10” dish with a vertically polarized feed for 10.7 to 11.7 GHz frequency range.
|
|
|
Ultra-Light EL/AZ / AL-1612-1
|
|
Airborne ultra-light multi positioner system, consisting of 3 gimbals AL-1612-1, all controlled by a single controller AL-1612-3.
|
|
|
Airborne MM Wave / AL-1615-1
|
|
Airborne Satellite Tracking Antenna System for communication with satellite.
The positioner supports a flat plate antenna, uniquely designed to require minimal radome volume. The control system tracks a geosynchronous satellite while subjected to the aircraft’s dynamic movements.
|
|
|
|
|
